Honeywell Humidifier BH-862E Manual

The Honeywell BH-862E is a cool mist humidifier designed to add comfortable moisture to dry air in medium to large rooms. It features a 1-gallon (3.8L) tank capacity, adjustable humidity control, a quiet operation mode, an easy-to-clean design, a built-in humidistat, an automatic shut-off function when empty, a refill indicator light, and a wicking filter. Below are key sections for safety, features, setup, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation & Setup 3. First-Time Use 4. Specifications 5. Controls and Operation 6. Maintenance & Cleaning 7. Filter Replacement 8. Safety Features 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Water Tank, Base Unit with Motor, Humidistat Control Dial, Mist Outlet, Power Cord, Wick Filter, and Refill Indicator Light.

Feature	Description
1-Gallon Tank	Removable tank for easy filling
Adjustable Humidity Control	Dial to set desired humidity level
Quiet Operation	Designed for low-noise performance
Automatic Shut-Off	Turns off when tank is empty
Refill Indicator Light	LED lights up when tank needs refilling
Wick Filter	Traps minerals and impurities; requires periodic replacement
Easy-Clean Design	Wide tank opening and accessible base
360° Mist Nozzle	Adjustable outlet to direct mist flow
Humidistat	Monitors room humidity and adjusts output
Carry Handle	Integrated handle on tank for easy transport

Installation & Setup

Unpack and inspect all contents. Place on a firm, flat, level surface away from walls and electronics.

Remove the water tank from the base unit.
Remove the wick filter from its packaging and install it onto the filter frame in the base.
Fill the tank with cool, clean tap or distilled water. Do not use hot water or additives.
Place the filled tank back onto the base, ensuring it is seated securely.
Plug the power cord into a standard 120V AC outlet.

WARNING! Place humidifier on a water-resistant surface. Keep cord away from heated surfaces and out of walkways.

First-Time Use

After setup, power on the humidifier and configure initial settings.

Turn the Humidity Control dial to the desired setting (e.g., 40-50% for comfort).
Adjust the 360° mist nozzle to direct moisture away from walls and furniture.
The unit will begin producing a cool mist. The refill light will be off when the tank is full.
Allow 24 hours for the wick to fully saturate and for the unit to reach optimal output.

CAUTION! Always use two hands when carrying a full water tank to prevent spills.

Specifications

Model: BH-862E
Tank Capacity: 1 Gallon (3.8 Liters)
Coverage Area: Up to 400 square feet
Run Time: Up to 24 hours on low setting
Output: Up to 1.2 gallons per day
Humidistat: Yes, adjustable
Noise Level: Quiet operation (< 35 dB on low)
Power: 120V AC, 60Hz, 30W
Dimensions (HxWxD): 16.5" x 10.2" x 10.5"
Weight (Empty): 5.5 lbs

Controls and Operation

Primary controls are located on the front of the base unit.

Humidity Control Dial: Turn clockwise to increase desired humidity level, counter-clockwise to decrease. The built-in humidistat will cycle the fan to maintain the set level.

Mist Nozzle: Rotate 360° to direct mist output.

Indicator Light: The green power light is on when plugged in. The red refill light illuminates when the water tank is empty or nearly empty.

Automatic Operation: The unit will automatically turn off when the tank is empty. It will resume when the tank is refilled and properly seated.

Maintenance & Cleaning

Regular cleaning prevents mineral buildup and microbial growth. Unplug the unit before any maintenance.

Daily: Refill with fresh water. Do not let water sit in tank for more than 2 days.
Weekly Cleaning: Empty all water. Clean tank and base with a soft cloth and a mixture of mild dish soap and warm water. Rinse thoroughly.
Descaling (Monthly or as needed): Use a solution of 1 cup white vinegar and 1 gallon water. Fill the base (not the tank) and let sit for 20 minutes. Scrub with a soft brush, rinse completely.
Dry all parts completely before reassembly and storage.

CAUTION! Never immerse the motor unit or base electronics in water. Do not use abrasive cleaners or bleach.

Filter Replacement

The wick filter should be replaced every 1-2 months, or when visibly discolored or hardened.

Unplug the humidifier and remove the water tank.
Lift out the old wick filter from the base.
Insert the new filter, ensuring it is seated flat on the filter frame.
Reassemble the unit. Allow 15-20 minutes for the new filter to fully absorb water before operation.

Tip: Using distilled water can extend filter life and reduce white dust.

Safety Features

Automatic Shut-Off: Turns the unit off when the water tank is empty, protecting the motor.

Tip-Over Protection: Some models include a switch that turns the unit off if tilted.

Cool Mist Technology: Produces room-temperature mist, eliminating burn risks associated with warm mist humidifiers.

Regulatory Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. Copyright and trademarks are property of Honeywell International Inc. For customer support, visit www.honeywellpluggedin.com or call 1-800-332-1110.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No mist output	Empty tank, clogged filter, unit unplugged	Refill tank. Replace filter. Ensure unit is plugged in and power outlet is working.
Red refill light is on	Tank is empty or not seated properly	Refill water tank. Remove and firmly reseat tank on base.
White dust on surfaces	Minerals in hard water	Use distilled or demineralized water. Replace filter more frequently.
Unpleasant odor	Dirty tank or old filter	Clean tank and base thoroughly with vinegar solution. Replace filter.
Unit is noisy	Low water level, mineral buildup, loose parts	Refill tank. Descale unit. Ensure tank is seated securely and all parts are tight.
Water leakage	Tank not seated, cracked tank, overfilled	Check tank seal and seating. Inspect for cracks. Do not overfill when filling.

Reset: Unplug unit for 2 minutes, then plug back in.

Service: For repairs, contact authorized Honeywell service center. Do not attempt to disassemble the motor unit.