Honeywell Humidifier HCM-890WTG Manual

The Honeywell HCM-890WTG is a 2.5-gallon cool mist humidifier with a wicking filter, designed for medium to large rooms up to 500 sq ft. It features a transparent water tank, adjustable humidity control, a 360-degree rotating mist nozzle, an auto shut-off function when empty, a filter change indicator, and a quiet operation mode. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: 2.5-gallon transparent water tank, wicking filter, control panel with digital display, 360-degree mist nozzle, filter change indicator, and power adapter.

Installation & Setup

Unpack and inspect all components. Place on a flat, stable surface away from direct sunlight and heat sources.

1. Remove all packaging materials from the humidifier and tank.
2. Install the wicking filter: Remove filter from package, soak in cool water for 15 minutes, then insert into filter compartment.
3. Fill the water tank: Carry tank to sink, remove cap, fill with cool tap water (do not use hot water), replace cap securely.
4. Place tank on base: Align tank with base and press down until seated properly.
5. Plug into a grounded 120V AC outlet.

WARNING! Do not operate without water. Ensure unit is on a level surface to prevent leakage.

First-Time Use

Power on the humidifier; the digital display will illuminate.

1. Set desired humidity: Press the HUMIDITY button to select 40%, 50%, or 60% RH.
2. Adjust mist output: Press the MIST button to cycle through Low, Medium, and High settings.
3. Rotate nozzle: Adjust the 360-degree nozzle to direct mist away from walls and furniture.
4. Monitor display: The digital readout shows current room humidity and selected settings.

CAUTION! Use only cool tap water. Do not add essential oils or other additives directly into the tank.

Specifications

• Model: HCM-890WTG
• Tank Capacity: 2.5 gallons (9.5 liters)
• Coverage Area: Up to 500 sq ft
• Output: Up to 1.2 gallons per day (24-hour runtime on Low setting)
• Humidity Control: Adjustable 40%-60% RH with digital display
• Noise Level: < 35 dB on Low setting
• Power Consumption: 30W maximum
• Power Requirements: 120V AC, 60Hz
• Dimensions: 15.5" H x 12.5" W x 10.5" D
• Weight: 8.5 lbs (empty)

Controls and Settings

Control Panel: POWER button, HUMIDITY selector (40%, 50%, 60%), MIST output (Low/Medium/High), FILTER indicator light, and digital display.

Display Information: Current room humidity percentage, selected humidity target, mist level icon, and filter replacement indicator.

Operation Modes: Normal mode (continuous operation), Quiet mode (reduced fan speed), and Auto mode (adjusts output based on room humidity). Timer: Can be set for 2, 4, 8, or 12 hours of operation.

Operation Guide

Daily operation procedures for optimal performance.

1. Check water level: Monitor transparent tank; refill when low.
2. Adjust settings: Change mist output based on room conditions.
3. Use timer: Press TIMER button to set automatic shut-off.
4. Enable quiet mode: Press and hold MIST button for 3 seconds for nighttime operation.
5. Monitor filter: Replace when FILTER indicator light turns red.

Tip: Place humidifier at least 12 inches from walls for proper air circulation.

Maintenance & Cleaning

Regular cleaning prevents mold and mineral buildup.

1. Unplug unit and empty water tank completely.
2. Clean tank: Use mild detergent and soft brush; rinse thoroughly.
3. Clean base: Wipe with damp cloth; do not submerge in water.
4. Descale monthly: Use white vinegar solution (1 part vinegar to 3 parts water) to remove mineral deposits.
5. Dry completely: Allow all parts to air dry before reassembly.

WARNING! Never use abrasive cleaners or bleach. Always unplug before cleaning.

Filter Replacement

The wicking filter should be replaced every 1-3 months depending on water hardness and usage.

1. Order replacement filter: Use genuine Honeywell Filter #HF-890.
2. Remove old filter: Open filter compartment, remove used filter.
3. Prepare new filter: Soak in cool water for 15 minutes before installation.
4. Install filter: Insert into compartment, ensuring proper alignment.
5. Reset indicator: Press and hold FILTER button for 5 seconds to reset light.

CAUTION! Do not operate without a filter installed. Using tap water may require more frequent replacements.

Safety Information

Important safety precautions for proper use.

• Always unplug before cleaning or maintenance.
• Use only cool tap water; never use hot water or additives.
• Keep out of reach of children and pets.
• Do not operate if cord or plug is damaged.
• Do not cover mist outlet or air intakes.
• Place on water-resistant surface to prevent water damage.
• Consult physician if you have respiratory conditions.

DANGER! Risk of electric shock. Do not immerse unit in water or other liquids.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. UL Listed: Meets UL 998 safety standards for humidifiers. Copyright © 2023 Honeywell International Inc. For support, visit www.honeywellhumidifiers.com or contact 1-800-332-1110. Manufactured for Honeywell Consumer Products, Atlanta, GA.

Troubleshooting

Reset: Unplug for 5 minutes, then restart to reset electronic controls.

Service: 1-800-332-1110; www.honeywellhumidifiers.com