Honeywell Humidifier HCM650 - Lon QuietCare Cool Moisture Manual

The Honeywell Humidifier HCM650 is a cool moisture humidifier designed to add moisture to dry indoor air, helping to relieve dry air discomfort. It features a quiet operation, a large tank capacity, an adjustable humidistat, a wicking filter, an easy-to-fill tank, an automatic shut-off when empty, and an indicator light. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Water Tank, Base Unit with Motor, Wicking Filter, Humidistat Control Knob, Tank Cap, Mist Outlet, Power Cord, and Indicator Light.

Installation & Setup

Unpack and inspect all contents. Place on a stable, level, waterproof surface.

1. Remove all packaging materials from the tank and base.
2. Install the wicking filter: Remove from package, soak in cool water for 15-20 minutes, then insert into the filter frame in the base.
3. Fill the tank: Remove tank cap, fill with cool, clean water. Replace cap securely.
4. Place the tank: Carefully position the filled tank onto the base unit.
5. Plug into a standard 120V AC electrical outlet.

WARNING! Place humidifier on a level surface at least 12 inches away from walls and furniture. Do not place on carpets or uneven surfaces. Use clean, cool water only.

First-Time Use

Power on the humidifier; adjust settings for desired comfort.

1. Power On: Plug in the unit. The indicator light will illuminate.
2. Set Humidity Level: Turn the humidistat control knob to the desired setting (Low to High).
3. Mist Output: Visible cool mist should begin to emit from the outlet. Adjust the control knob to increase or decrease output.
4. Run Time: The unit will run until the tank is empty or turned off. The automatic shut-off will activate when the tank is empty.

CAUTION! Always turn the control knob to OFF and unplug the unit before moving, cleaning, or refilling.

Specifications

• Model: HCM650 (Lon QuietCare Cool Moisture)
• Tank Capacity: 1.5 Gallons (approx. 5.7 Liters)
• Room Coverage: Up to 2500 sq. ft. for 24 hours (on high setting)
• Moisture Output: Up to 2.3 gallons per day
• Operation: Cool Mist
• Noise Level: Ultra-Quiet (QuietCare Technology)
• Controls: Adjustable Humidistat Dial
• Filter Type: Replaceable Wicking Filter (Model HF-60)
• Power Source: 120V AC, 60Hz
• Automatic Shut-Off: Yes (when empty)

Controls and Operation

Primary control is the Humidistat Dial on the front of the base unit.

Dial Positions: OFF, LOW, MEDIUM, HIGH. Turning the dial clockwise increases moisture output.

Indicator Light: A blue or green light (model dependent) illuminates when the unit is plugged in and operational. It does not indicate water level.

Automatic Operation: Set the dial to desired humidity level. The unit will run until the tank is empty, then shut off automatically. Refill the tank to resume operation.

Tip: For best results, keep doors to the room closed. Use a hygrometer to monitor room humidity (ideal range is 30-50%).

Maintenance & Cleaning

Regular cleaning prevents mineral buildup and microbial growth. Clean every 1-2 weeks during use.

1. Unplug the unit and remove the water tank.
2. Empty any remaining water from the tank and base.
3. Clean Tank: Use a soft cloth or brush with a mild detergent (e.g., dish soap) and warm water. Rinse thoroughly. Do not immerse the tank cap.
4. Clean Base: Wipe the base reservoir with a damp cloth. Use a vinegar solution (1 part white vinegar to 3 parts water) to descale mineral deposits. Rinse thoroughly.
5. Dry: Allow all parts to air dry completely before reassembly.

WARNING! Never use abrasive cleaners, bleach, or harsh chemicals. Do not immerse the motor unit/base in water.

Replacing the Filter

The wicking filter should be replaced every 1-2 months during the season, or when visibly discolored or clogged.

1. Unplug the unit and remove the water tank.
2. Remove the old filter from the filter frame in the base.
3. Soak the new filter (Model HF-60) in cool water for 15-20 minutes.
4. Insert the soaked filter into the filter frame, ensuring it is seated properly.
5. Reassemble the tank and base, then plug in the unit.

Note: Using the humidifier without a filter or with a clogged filter can reduce performance and cause mineral dust (white dust).

Safety Features

Automatic Shut-Off: Turns the unit off when the water tank is empty, preventing the motor from running dry.

Tip-Over Protection: Some models include a switch that turns the unit off if it is tipped over.

Over-Humidification Prevention: The adjustable humidistat allows you to control output to prevent excessive moisture.

CAUTION! This is an electrical appliance. Keep away from children. Do not operate with a damaged cord or plug. Do not block the mist outlet.

Care & Storage

When not in use for an extended period (e.g., summer months), prepare the unit for storage.

1. Unplug the unit.
2. Empty and thoroughly clean the tank and base as described in the Cleaning section.
3. Remove and discard the old wicking filter.
4. Allow all parts to dry completely.
5. Reassemble the unit without a filter. Store in its original box or a clean, dry place.
6. Install a new filter at the start of the next season.

Tip: Do not store with water in the tank, as this can lead to mold or bacterial growth.

Regulatory Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. Copyright and trademarks are property of Honeywell International Inc. For support, replacement filters, and more information, visit www.honeywellpluggedin.com or contact customer service at 1-800-332-1110.

Troubleshooting

Reset: Unplug the unit for 5 minutes, then plug back in.

Service: For persistent issues, contact Honeywell Customer Service at 1-800-332-1110 or visit www.honeywellpluggedin.com. Do not attempt to repair the unit yourself.