Honeywell Humidifier HE120A Manual

The Honeywell Humidifier HE120A is a high-capacity evaporative humidifier designed for large rooms up to 1200 sq. ft. It features a 1.5-gallon tank, three fan speeds, an adjustable humidistat, automatic shut-off, a refill indicator, and a wick filter system. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting to Power 7. Operation 8. Maintenance 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Water tank, wick filter, fan assembly, control panel, humidistat, power cord.

Feature	Description
Water Tank	1.5-gallon capacity with carry handle
Wick Filter	Evaporative filter for moisture release
Fan Speeds	Three settings (Low, Medium, High)
Adjustable Humidistat	Set desired humidity level
Automatic Shut-Off	Turns off when tank is empty
Refill Indicator	Light alerts when tank needs refilling
Control Panel	Buttons for power, fan speed, humidistat
Carry Handle	For easy tank transport
Power Cord	6-foot cord with plug
Filter Change Indicator	Reminds when to replace wick

Installation

Unpack and inspect contents. Place on level, stable surface away from walls and furniture.

Remove tank: Lift tank from base unit.
Install wick filter: Insert filter into slot in base, ensuring it sits properly.
Fill tank: Turn tank upside down, remove cap, fill with clean water, replace cap.
Replace tank: Place tank back on base, aligning properly.
Position unit: Place on floor or sturdy surface in center of room for best airflow.

WARNING! Do not place on carpets or near heat sources. Ensure unit is upright before filling.

First-Time Setup

After installation, prepare for operation.

Plug in: Connect power cord to grounded outlet.
Power on: Press POWER button; unit will beep.
Set fan speed: Press FAN button to select Low, Medium, or High.
Set humidity: Turn HUMIDISTAT knob to desired level (30-60% recommended).
Allow operation: Unit will begin humidifying; tank may take a few minutes to saturate filter.

CAUTION! Use only clean, cool water. Do not add additives or essential oils.

Specifications

Model: HE120A
Coverage: Up to 1200 sq. ft.
Tank Capacity: 1.5 gallons
Output: Up to 2.5 gallons per day
Fan Speeds: 3 (Low, Medium, High)
Humidistat: Adjustable, 30-60% range
Power: 120V AC, 60Hz, 40W max
Dimensions: 15.5" H x 13.2" W x 10.8" D
Weight: 8.5 lbs (empty)
Filter Type: Evaporative wick (replace every 1-3 months)

Controls and Settings

Control Panel: POWER button, FAN button, HUMIDISTAT knob, indicator lights.

Power: Press to turn unit on/off. Fan: Cycles through Low, Medium, High speeds. Humidistat: Turn knob to set target humidity (30-60%). Indicators: Power (green), Refill (red), Filter Change (yellow).

Operation Modes: Continuous run (fan on) or automatic (humidistat controls fan based on room humidity).

Connecting to Power

Use only grounded 120V AC outlet.

Ensure unit is off and tank is filled.
Plug power cord into outlet.
Press POWER button to start.

Tip: Use a surge protector for added safety. Do not use extension cords.

Operation

For daily use.

Fill tank daily: Remove tank, fill with clean water, replace.
Adjust settings: Use FAN and HUMIDISTAT as needed.
Monitor indicators: Refill light means tank is empty; Filter light means replace wick.
Automatic shut-off: Unit turns off when tank is empty; refill to restart.
Night mode: Set fan to Low for quiet operation.

WARNING! Do not operate without water or with damaged filter. Unplug before maintenance.

Maintenance

Regular maintenance ensures performance and longevity.

Daily: Refill tank as needed.
Weekly: Wipe exterior with damp cloth.
Monthly: Clean tank with mild soap, rinse thoroughly.
Every 1-3 months: Replace wick filter (or when indicator lights).
Seasonal: Deep clean base unit before storage.

Note: Use only genuine Honeywell replacement filters (Part # HE120A-FILTER).

Care & Cleaning

Unplug before cleaning. Use mild soap and water; no harsh chemicals.

Tank: Remove, empty, clean with soapy water, rinse, dry.
Base: Wipe with damp cloth; do not submerge.
Filter: Replace when discolored or mineralized; do not wash.
Exterior: Dry cloth for control panel and housing.

CAUTION! Do not use bleach, vinegar, or abrasive cleaners. Ensure all parts are dry before reassembly.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. UL listed for safety. Copyright © Honeywell International Inc. For support, visit www.honeywellhumidifiers.com or contact 1-800-332-1110.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Unit not turning on	No power	Check outlet; ensure plug is secure; press POWER button.
No mist/output	Empty tank, clogged filter	Refill tank; replace wick filter; ensure tank is seated.
Red refill light on	Tank empty	Refill tank with water.
Yellow filter light on	Filter needs replacement	Replace wick filter with new one.
Unusual noise	Fan obstruction, loose parts	Check for debris; ensure filter is installed correctly.
Water leakage	Overfilled tank, damaged seal	Do not overfill; check tank cap and seals; place on level surface.
Humidity too low/high	Incorrect humidistat setting	Adjust humidistat; ensure room size matches coverage.

Reset: Unplug for 30 seconds, then restart.

Service: 1-800-332-1110; www.honeywellhumidifiers.com