Honeywell Humidifier HE120A1027 Manual

The Honeywell Humidifier HE120A1027 is a cool moisture console humidifier designed for medium to large rooms up to 2300 sq. ft. It features a 1.5-gallon tank capacity, three speed settings (Low, Medium, High), a 24-hour programmable humidistat, digital controls with an easy-to-read display, an antimicrobial-treated filter, an empty tank indicator, automatic shut-off, and a refill indicator. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Water Tank, Humidifier Base with Control Panel, Demineralization Cartridge (if included), Wick Filter, and Power Adapter.

Installation & Setup

Unpack and inspect all contents. Place on a level, stable surface at least 12 inches from walls.

1. Install the Filter: Remove filter from packaging, soak in cool water for 15-20 minutes, then insert into filter frame in base.
2. Prepare the Tank: Remove tank cap, fill with cool, clean water up to the fill line, replace cap securely.
3. Assemble Unit: Place water tank onto the base, ensuring it sits firmly and evenly.
4. Power Connection: Plug the power cord into a standard 120V AC outlet.

WARNING! Use only clean, cool water. Do not use hot water or add fragrances/oils. Ensure unit is on a waterproof surface.

First-Time Use

Power on the humidifier; the digital display will illuminate.

1. Set Desired Humidity: Press the HUMIDITY button to set your target humidity level (recommended 30-50%).
2. Select Fan Speed: Press the SPEED button to cycle through Low, Medium, and High settings.
3. Program Timer (if needed): Use the TIMER button to set automatic shut-off after 1-24 hours.
4. Monitor Operation: The display will show current room humidity and set parameters.

CAUTION! Always place the humidifier on a flat, stable surface away from heat sources and electronics.

Specifications

• Model: HE120A1027
• Coverage Area: Up to 2300 sq. ft.
• Tank Capacity: 1.5 gallons (5.7 liters)
• Output: Up to 2.3 gallons per day (depending on settings)
• Fan Speeds: 3 (Low, Medium, High)
• Humidistat: Digital, programmable 24-hour
• Filter Type: Antimicrobial wick filter
• Power Source: 120V AC, 60Hz
• Power Consumption: 40W (max)
• Unit Dimensions: 17.5" H x 13.5" W x 10.5" D
• Weight (empty): 9.5 lbs

Controls and Settings

Access all functions via the digital control panel on the front of the unit.

Control Panel Buttons: POWER, HUMIDITY (+/-), SPEED, TIMER, FILTER RESET.

Display Icons: Power, Current Humidity, Set Humidity, Fan Speed, Timer, Empty Tank, Refill, Filter Change.

Settings: Target Humidity (30-60% adjustable), Fan Speed (Low/Medium/High), Timer (1-24 hours in 1-hour increments), Filter Reset (hold for 3 seconds after filter replacement).

Operation

For daily operation, ensure tank is filled and filter is properly installed.

1. Power On: Press POWER button; display lights up.
2. Adjust Settings: Set desired humidity and fan speed.
3. Automatic Operation: Unit will run until target humidity is reached, then cycle on/off to maintain it.
4. Refilling: When EMPTY indicator lights, remove tank, refill with cool water, and replace.
5. Night Mode: Press and hold POWER for 3 seconds to dim display lights.

Tip: For maximum efficiency, keep doors closed in the room being humidified.

Maintenance & Cleaning

Regular cleaning prevents mold and mineral buildup.

1. Daily: Wipe exterior with a soft, damp cloth.
2. Weekly Cleaning: Unplug unit. Remove tank and empty any remaining water. Clean tank with mild soap and water, rinse thoroughly. Wipe base interior with a damp cloth.
3. Monthly Deep Clean: Prepare a solution of 1 teaspoon white vinegar per gallon of water. Use to clean tank and base, then rinse thoroughly with clean water.
4. Dry all parts completely before reassembly.

WARNING! Never immerse base in water. Unplug before cleaning. Do not use abrasive cleaners.

Filter Replacement

Replace the wick filter every 1-3 months, or when FILTER CHANGE indicator lights.

1. Unplug unit and remove water tank.
2. Remove old filter from the frame in the base.
3. Soak new filter in cool water for 15-20 minutes.
4. Insert new filter into frame, ensuring it sits flat.
5. Press and hold FILTER RESET button for 3 seconds to reset indicator.
6. Reassemble unit and refill tank.

Note: Use only genuine Honeywell replacement filters (Part # HE120A1001) for optimal performance.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. ETL Listed. Copyright © Honeywell International Inc. For support, visit www.honeywellhumidifiers.com or contact 1-800-332-1110.

Troubleshooting

Reset: Unplug unit for 60 seconds, then plug back in to reset electronics.

Service: 1-800-332-1110; www.honeywellhumidifiers.com