Honeywell Humidifier HE160 Manual

The Honeywell Humidifier HE160 is a cool mist humidifier designed to add moisture to dry indoor air, helping to relieve dry skin, nasal congestion, and static electricity. It features a 1-gallon tank capacity, adjustable humidity control, a wicking filter system, an easy-to-fill tank, a quiet operation mode, an automatic shut-off when empty, and an indicator light. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Water Tank, Base Unit with Motor, Wicking Filter, Humidity Control Dial, Power Cord, Indicator Light, Mist Outlet.

Installation & Setup

Unpack and inspect all parts. Place on a flat, stable, level surface away from walls and electronics.

1. Remove the water tank from the base unit.
2. Install the wicking filter: Remove from packaging, soak in cool water for 15 minutes, then insert into the filter compartment in the base.
3. Fill the tank: Turn tank upside down, remove cap, fill with cool, clean water (do not use hot water or additives). Replace cap securely.
4. Place tank back on base, ensuring it sits firmly and evenly.
5. Plug the power cord into a standard 120V AC outlet.

WARNING! Place humidifier on a water-resistant surface. Keep away from children. Do not operate without water or filter installed.

First-Time Use

After installation, follow these steps to begin operation.

1. Ensure the unit is unplugged during initial setup.
2. Set the humidity control dial to the desired setting (Low, Medium, High).
3. Plug in the unit. The indicator light will illuminate.
4. Mist should begin to emit from the outlet within a few minutes.
5. Adjust the dial to achieve your preferred humidity level and mist output.

CAUTION! Use only clean, cool tap or distilled water. Do not add essential oils, fragrances, or other chemicals to the water tank.

Specifications

• Model: HE160
• Tank Capacity: 1 Gallon (3.8 Liters)
• Run Time: Up to 24 hours (Low setting)
• Room Coverage: Up to 250 square feet
• Mist Output: Adjustable, up to 1.2 gallons per day
• Technology: Cool Mist Evaporative
• Filter Type: Wicking Demineralization Filter (Replace every 1-2 months)
• Power: 120V AC, 60Hz, 23W
• Dimensions (L x W x H): Approx. 10.5" x 10.5" x 13.5"
• Weight (Empty): 4.5 lbs

Controls and Settings

The humidifier features simple, intuitive controls located on the front of the base unit.

Main Control Dial: Rotate to select mist output level. Settings typically include OFF, LOW, MEDIUM, and HIGH. Turning to OFF powers down the fan but does not disconnect power.

Indicator Light: A blue or green LED illuminates when the unit is plugged in and powered on. It does not indicate water level.

Automatic Shut-Off: A float mechanism turns off the fan motor when the water tank is empty to prevent damage.

Tip: For optimal humidity (30-50%), start on a medium setting and adjust based on room conditions.

Operation

Daily operation is straightforward once set up.

1. Check the water level daily. Refill when tank is low or empty.
2. To refill: Unplug unit, remove tank, fill with cool water, replace on base.
3. Adjust the control dial as needed for comfort. Lower settings are quieter and use less water.
4. Use in a closed room for best results. Keep mist outlet clear of obstructions.
5. To turn off, rotate dial to OFF and unplug from the outlet.

Tip: Using distilled water can reduce mineral dust (white dust) and extend filter life.

Maintenance & Cleaning

Regular cleaning prevents mold, bacteria, and mineral buildup.

1. Daily: Wipe exterior with a damp cloth.
2. Weekly/Bi-Weekly: Deep clean tank and base.
   • Unplug unit. Empty any remaining water.
   • Disassemble: Remove tank, filter, and any removable parts.
   • Clean tank and base with a mixture of 1 teaspoon of white vinegar and 1 gallon of water. Use a soft brush for hard-to-reach areas.
   • Rinse all parts thoroughly with clean water to remove vinegar residue.
   • Allow all parts to air dry completely before reassembly.
3. Never immerse the motorized base in water. Wipe with a damp cloth only.

CAUTION! Do not use harsh chemicals, abrasives, or detergents. Always unplug before cleaning.

Filter Replacement

The wicking filter should be replaced every 1-2 months for optimal performance, or more often if using hard water.

1. Unplug the humidifier and remove the water tank.
2. Remove the old filter from the base compartment.
3. Soak the new filter (Model HF-160) in cool water for 15 minutes.
4. Insert the damp filter into the compartment, ensuring it is seated properly.
5. Reassemble the tank and base. The unit is ready for use.

Note: A clogged or old filter will reduce mist output and efficiency. Dispose of old filter according to local regulations.

Safety Information

To ensure safe operation, please adhere to the following:

• Use only as directed in this manual.
• Intended for indoor household use only.
• Always place on a firm, flat, level, and water-resistant surface.
• Keep out of reach of children and pets.
• Do not operate without water or without the filter properly installed.
• Do not cover the mist outlet or block air intake vents.
• Never move or carry the unit while it is operating or filled with water.
• Do not attempt to repair the unit yourself. Contact customer service for assistance.

WARNING! Risk of electric shock. Do not plug or unplug with wet hands. Always unplug before cleaning, maintenance, or when not in use for extended periods.

Regulatory Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. This product meets applicable U.S. safety standards. Honeywell is a trademark of Honeywell International Inc., used under license. For support, visit www.honeywellhumidifiers.com or contact 1-800-332-1110.

Troubleshooting

Reset: Unplug unit for 5 minutes, then restart. Ensure filter is clean and properly installed.

Service: For persistent issues, contact Honeywell Customer Service at 1-800-332-1110 or visit www.honeywellhumidifiers.com.