Honeywell Humidifier HE200A1000 Manual

The Honeywell Humidifier HE200A1000 is a cool moisture console humidifier designed for large rooms up to 2300 sq. ft. It features a 2.5-gallon tank capacity, three fan speeds (High, Medium, Low), an adjustable humidistat for automatic operation, a refill indicator light, a wick filter system, and a directional mist outlet. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Water Tank, Base Unit with Fan and Motor, Wick Filter, Humidistat Control Panel, Refill Indicator, Directional Mist Outlet.

Installation & Setup

Unpack and inspect all components. Place on a level, stable surface away from walls and furniture.

1. Remove the water tank from the base unit.
2. Install the wick filter: Remove from packaging and insert into the filter frame in the base.
3. Fill the tank with cool, clean water. Do not use hot water or additives.
4. Place the filled tank back onto the base, ensuring it is seated properly.
5. Plug the power cord into a standard 120V AC outlet.

WARNING! Place humidifier on a waterproof mat or towel on finished floors. Ensure the unit is level to prevent leaking.

First-Time Use

Power on the humidifier; set initial controls.

1. Turn the humidistat knob to the desired humidity level (e.g., 45-50% for comfort).
2. Select fan speed: Start on HIGH for quick humidity boost, then switch to MEDIUM or LOW.
3. Adjust the directional louvers to aim moisture away from walls and furniture.
4. The unit will run until the desired humidity is reached, then cycle on/off automatically.

CAUTION! Always use two hands when carrying the filled water tank. Do not operate without the wick filter installed.

Specifications

• Model: HE200A1000
• Type: Cool Moisture Console Evaporative Humidifier
• Room Coverage: Up to 2300 sq. ft.
• Tank Capacity: 2.5 Gallons (9.5 L)
• Output: Up to 2.3 gallons per day (depending on fan speed and room conditions)
• Fan Speeds: 3 (High, Medium, Low)
• Controls: Rotary Humidistat, Fan Speed Switch
• Power: 120V AC, 60Hz
• Power Consumption: 40W (Max)
• Filter Type: Replaceable Wick Filter (Model HWF200)
• Dimensions (L x W x H): 18.5" x 15.5" x 20.5"
• Weight (Empty): 12.5 lbs

Controls and Settings

Control Panel located on the front of the base unit.

Humidistat Knob: Turn to set desired room humidity level (Low to High). The unit will automatically turn the fan on/off to maintain this level.
Fan Speed Switch: Selects motor/fan speed: HIGH (maximum output), MEDIUM (balanced), LOW (quiet operation).
Refill Indicator Light: Red LED illuminates when the water tank is empty and needs refilling.
Power Indicator: Blue LED indicates unit is receiving power.

Tip: For energy savings, set the humidistat to the lowest comfortable setting (usually 40-50% RH).

Operation Modes

Automatic Mode: Set the humidistat to desired level. The unit monitors humidity and runs only when needed.
Continuous Mode: Set humidistat to maximum (or "ON") and choose fan speed. The unit will run continuously until turned off or tank is empty.
Night Mode: Use LOW fan speed for quiet operation during sleep.

1. For dry winter conditions, start with humidistat at 45% and HIGH fan.
2. Once room humidity stabilizes, reduce fan speed to MEDIUM or LOW.
3. Adjust louvers to distribute moisture evenly.

WARNING! Do not block air inlet (back) or outlet (front). Operate on a stable, level surface only.

Maintenance & Cleaning

Regular cleaning prevents mold and mineral buildup. Unplug the unit before any maintenance.

1. Daily: Refill tank with clean, cool water.
2. Weekly: Wipe exterior with a soft, damp cloth.
3. Bi-Weekly (or as needed): Clean the water tank and base.
   • Empty all water.
   • Use a soft brush and mild detergent (if needed) to scrub interior surfaces.
   • Rinse thoroughly with clean water.
   • Dry with a soft cloth before refilling.
4. End of Season: Perform a deep clean (see manual) before storage.

CAUTION! Never immerse the base unit, motor, or electrical parts in water. Do not use abrasive cleaners or chemicals.

Filter Replacement

The wick filter (Model HWF200) should be replaced every 1-2 months during the season, or when visibly coated with mineral deposits or discolored.

1. Unplug the humidifier and remove the water tank.
2. Lift out the old wick filter from the base frame.
3. Insert the new wick filter. Ensure it is fully seated and the frame is closed.
4. Reinstall the water tank and plug in the unit.
5. Run the humidifier on HIGH for 10 minutes to prime the new filter.

Tip: Using demineralization cartridges or distilled water can extend filter life.

Safety Information

Important Safety Instructions: Read all instructions before use.

• Use only 120V AC outlet.
• Do not operate with a damaged cord or plug.
• Always place on a level, stable, and waterproof surface.
• Keep out of reach of children and pets.
• Do not cover or block air openings.
• Never add essential oils, fragrances, or chemicals to the water tank.
• Unplug before cleaning, maintenance, or when not in use for extended periods.
• Do not move or carry the unit while it is operating or filled with water.

Regulatory Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. Copyright © Honeywell International Inc. Honeywell and the Honeywell logo are registered trademarks of Honeywell International Inc. For support, replacement filters, and accessories, visit www.honeywellpluggedin.com or contact Consumer Support at 1-800-332-1110.

Troubleshooting

Reset: Unplug unit for 60 seconds, then plug back in.

Service: For repairs, contact authorized service center. Do not attempt to disassemble the unit.