Honeywell Humidifier Kaz HUT-220 Series Manual

The Honeywell HUT-220 Series is a cool mist humidifier designed to add moisture to dry air, helping to relieve discomfort associated with dry air such as dry skin, irritated nasal passages, and static electricity. It features a 1-gallon tank capacity, adjustable mist control, an easy-to-fill tank design, a wicking filter system, and an automatic shut-off when empty. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Water Tank, Base Unit with Mist Outlet, Control Knob, Filter, and Power Cord.

Installation & Setup

Unpack and inspect all contents. Place on a flat, stable, level surface away from direct sunlight and heat sources.

1. Remove all packaging materials from the humidifier and tank.
2. Install the wicking filter: Remove filter from packaging, soak in cool water for 15 minutes, then insert into the filter compartment in the base.
3. Fill the tank: Carry tank to sink, remove cap, fill with cool, clean water. Replace cap securely.
4. Place tank on base: Align tank with base and set it down firmly. Ensure it is seated properly.
5. Plug into a standard 120V AC electrical outlet.

WARNING! Use only clean, cool water. Do not use hot water or add any chemicals, oils, or fragrances to the water tank. Ensure the unit is on a stable, waterproof surface.

First-Time Use

After installation, follow these steps to begin operation.

1. Ensure the tank is filled with cool water and properly seated on the base.
2. Plug the power cord into an electrical outlet.
3. Turn the Mist Control Knob to the desired setting (Low, Medium, or High).
4. The unit will begin producing a visible cool mist from the outlet.
5. Adjust the 360° mist outlet to direct the moisture as needed.

CAUTION! Do not operate without water. Do not block the mist outlet. Keep out of reach of children.

Specifications

• Model Series: HUT-220
• Tank Capacity: 1 Gallon (3.8 Liters)
• Run Time: Up to 24 hours (Low setting)
• Room Coverage: Up to 250 sq. ft.
• Mist Output: Adjustable, up to 0.5 gallons per day
• Filter Type: Replaceable wicking filter (Model HWF-220)
• Power: 120V AC, 60Hz
• Power Consumption: 25W
• Dimensions (L x W x H): Approx. 10.5" x 10.5" x 13.5"
• Weight (Empty): 4.5 lbs

Controls and Operation

The humidifier is operated primarily via the Mist Control Knob on the base unit.

Control Knob Positions:
OFF: Unit is powered off.
LOW (I): Minimum mist output for quiet operation and extended run time.
MEDIUM (II): Moderate mist output.
HIGH (III): Maximum mist output for rapid humidification.

Operation Tips:
- For best results, use in a closed room.
- Ideal humidity level is between 40% and 60%. Use a hygrometer to monitor.
- If white dust appears, use demineralization cartridges or distilled water.
- The automatic shut-off will activate when the water tank is empty. Refill to resume operation.

Maintenance & Cleaning

Regular cleaning is essential to prevent mold and mineral buildup.

1. Daily: Check water level and refill as needed.
2. Weekly Cleaning:
   • Unplug the unit.
   • Remove the water tank and empty any remaining water.
   • Clean the tank with a mixture of mild dish soap and warm water. Rinse thoroughly.
   • Wipe the base interior and exterior with a damp, soft cloth. Do not immerse base in water.
   • Allow all parts to air dry completely before reassembling.
3. Descaling (Monthly or as needed):
   • To remove mineral deposits, use a solution of 1 cup white vinegar and 1 gallon water.
   • Fill the tank with the solution, let sit for 20 minutes, then scrub gently. Rinse multiple times until vinegar smell is gone.

WARNING! Always unplug the unit before cleaning. Never use abrasive cleaners, bleach, or chemicals.

Filter Replacement

The wicking filter should be replaced every 1-2 months, or more often if you have hard water or use the unit frequently.

1. Unplug the humidifier and remove the water tank.
2. Locate the filter compartment in the base.
3. Remove the old filter and discard it.
4. Soak the new HWF-220 filter in cool water for 15 minutes.
5. Insert the damp filter into the compartment, ensuring it is seated properly.
6. Reassemble the tank and base, then plug in the unit.

Note: Using the humidifier without a filter or with a clogged filter can reduce performance and cause mineral dust.

Safety Features

Automatic Shut-Off: Turns the unit off when the water tank is empty, preventing damage to the motor.
Tip-Over Protection: Some models may include a feature to shut off if the unit is knocked over.
Water Leak Prevention: Sealed base design helps contain water in the tank.

Always place the humidifier on a flat, stable, waterproof surface. Do not use in an area where it is likely to get wet from external sources.

Care & Storage

When not in use for an extended period, prepare the humidifier for storage.

1. Unplug the unit.
2. Empty and thoroughly clean the tank and base as described in the cleaning section.
3. Remove and discard the old filter. Do not store the unit with a wet filter inside.
4. Allow all parts to air dry completely.
5. Reassemble the unit and store in its original box or a clean, dry place.

CAUTION! Never store the unit with water in the tank, as this can lead to mold growth and damage.

Regulatory Information

This humidifier complies with relevant U.S. safety standards. Copyright and trademarks are property of Honeywell International Inc. or its licensors. For customer support, replacement parts, or filter purchases, visit www.honeywellpluggedin.com or contact 1-800-332-1110.

Troubleshooting

Reset: Unplug the unit for 5 minutes, then plug back in.

Service: For repairs not covered in this manual, contact Honeywell Customer Service at 1-800-332-1110 or visit www.honeywellpluggedin.com. Do not attempt to disassemble the unit yourself.