Honeywell Humidifier TRADELINE HC22A Manual

The Honeywell Humidifier TRADELINE HC22A is a high-capacity console humidifier designed for large rooms up to 2300 sq. ft. It features a 2.2-gallon output per day, dual-speed fan control, adjustable humidity control (humidistat), easy-to-clean tank design, wick filter system, automatic shut-off, and refill indicator light. Operates on 120V AC. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Main console unit, Water Tank, Wick Filter, Humidistat Control Knob, Fan Speed Switch, Power Indicator Light, Refill Indicator Light.

Installation & Placement

Unpack and inspect all parts. Choose a level location on a firm, flat floor.

1. Remove humidifier from packaging and remove all protective materials.
2. Place unit on a level, waterproof surface at least 12 inches from walls and furniture.
3. Ensure the unit is placed away from heat sources, direct sunlight, and high-traffic areas.
4. Install the wick filter: Remove from plastic bag and insert into the base unit slots.
5. Fill the water tank with clean, cool tap water (see Section 6).

WARNING! Do not place on carpets or uneven surfaces. Ensure proper ventilation around the unit.

First-Time Setup

Prepare the humidifier for initial use.

1. Install the wick filter: Insert it into the slots in the base until it sits firmly.
2. Fill the water tank: Carry tank to water source, fill with clean tap water, and replace cap securely.
3. Place tank on base: Align tank with base unit and set down gently until seated.
4. Plug power cord into a 120V AC outlet.
5. Turn humidistat knob to desired humidity level (recommended 35-50% for comfort).
6. Select fan speed: Use the fan switch for High (quick humidification) or Low (quiet operation).

CAUTION! Never operate without the wick filter installed. Do not overfill the water tank.

Specifications

• Model: Honeywell TRADELINE HC22A
• Type: Console Evaporative Humidifier
• Room Coverage: Up to 2300 sq. ft.
• Output: 2.2 gallons per day (maximum)
• Tank Capacity: 2.2 gallons (8.3 liters)
• Humidity Control: Adjustable humidistat
• Fan Speeds: 2 (High and Low)
• Power: 120V AC, 60Hz
• Power Consumption: 40W (High), 25W (Low)
• Dimensions (approx.): 16.5" H x 13.5" W x 11.5" D
• Weight (empty): 10.5 lbs
• Noise Level: Low speed: < 40 dB

Controls and Operation

Front Panel Controls: Humidistat Knob, Fan Speed Switch (High/Low), Power Indicator Light, Refill Indicator Light.

Operation: Set humidistat to desired level (30-60% typical). Select fan speed. Unit will run until desired humidity is reached, then cycle on/off automatically. The refill light will illuminate when the water tank is empty.

Humidistat: Adjusts the desired room humidity level. Turn clockwise to increase, counter-clockwise to decrease.

Fan Speed: High for maximum output, Low for quieter operation and energy savings.

Filling the Water Tank

1. Turn off the unit and unplug it from the electrical outlet.
2. Grasp the tank handle and lift the water tank straight up off the base.
3. Carry the tank to a sink or water source. Remove the tank cap.
4. Fill the tank with clean, cool tap water. Do not use hot water or additives.
5. Replace the tank cap securely and ensure it is tight to prevent leaks.
6. Carry the tank back to the unit and place it gently onto the base, aligning it properly.
7. Plug the unit back in. The refill light will turn off once the tank is detected.

Tip: For easier cleaning, empty and rinse the tank weekly. Always refill with fresh water.

Maintenance & Cleaning

Regular cleaning prevents mold and mineral buildup.

1. Weekly: Empty, rinse, and refill the water tank with fresh water.
2. Bi-Weekly: Clean the base unit: Unplug, remove tank and wick. Wipe interior with a soft cloth dampened with a mixture of white vinegar and water (1:1). Rinse thoroughly.
3. Monthly: Deep clean all parts. Soak wick filter in vinegar solution if scaled, then rinse (see Wick Replacement section).
4. Dry all parts completely before reassembly.

CAUTION! Unplug before cleaning. Never immerse the base unit in water. Do not use harsh chemicals or abrasives.

Wick Filter Replacement

The wick filter should be replaced every 1-2 months during use, or when visibly scaled or damaged.

1. Unplug the humidifier and remove the water tank.
2. Remove the old wick filter by pulling it up and out of the base slots.
3. Dispose of the old filter properly.
4. Unpack the new wick filter (Honeywell part # HC-22).
5. Insert the new wick filter into the base slots, ensuring it is seated firmly and evenly.
6. Replace the water tank and plug in the unit.

Note: Using a dirty or clogged wick reduces efficiency and output. Use only genuine Honeywell replacement filters.

Safety Features

Automatic Shut-Off: Turns the unit off when the water tank is empty or improperly seated to prevent dry running and motor damage.

Tip-Over Protection: Internal switch cuts power if the unit is tipped over.

Refill Indicator: Red light alerts you when the tank needs refilling.

Important: Always operate on a stable, level surface. Use only with a properly installed wick filter.

Regulatory Information

This humidifier complies with applicable FCC standards. Copyright © Honeywell International Inc. TRADELINE is a trademark of Honeywell. For customer support, replacement parts, or to locate a service center, visit www.honeywellhumidifiers.com or call 1-800-332-1110.

Disposal: Dispose of the unit and its components in accordance with local electronic waste regulations. The wick filter is not recyclable and should be disposed of with regular household waste.

Troubleshooting

Reset: Unplug unit for 5 minutes, then plug back in.

Service: For persistent issues, contact Honeywell Customer Service at 1-800-332-1110 or visit www.honeywellhumidifiers.com.