Honeywell Humidifier TRADELINE HC26A Manual

The Honeywell Humidifier TRADELINE HC26A is a high-capacity evaporative humidifier designed for whole-room moisture control. It features a 2.6-gallon tank, adjustable humidistat, wicking filter system, automatic shut-off, quiet operation, and easy-to-clean design. Ideal for medium to large rooms up to 600 sq ft. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: 2.6-gallon water tank, Wicking Filter, Humidistat Control Knob, Power Switch, Water Level Indicator, Air Outlet Grille, Tank Handle, Base Unit.

Installation & Setup

Unpack and inspect all contents. Place on a flat, stable surface away from walls and electronics.

1. Remove all packaging materials from tank and base.
2. Install wicking filter: Remove filter from plastic bag and insert into base slots.
3. Fill tank with clean, cool tap water. Do not use hot water or additives.
4. Place tank securely onto base unit, ensuring proper alignment.
5. Plug power cord into a standard 120V AC outlet.

WARNING! Place humidifier on a water-resistant surface. Keep cord away from heated surfaces. Do not immerse unit in water.

First-Time Use

Power on the humidifier and adjust settings for optimal performance.

1. Turn the humidistat knob to the desired humidity level (typically 40-50% for comfort).
2. Press the power switch to ON. The indicator light will illuminate.
3. Allow 15-20 minutes for the filter to fully saturate and begin humidifying.
4. Adjust fan speed if available (models with multiple settings).
5. Monitor room humidity with a hygrometer for best results.

CAUTION! Always use clean water to prevent mineral buildup and microbial growth. Never operate without the filter installed.

Specifications

• Model: TRADELINE HC26A
• Tank Capacity: 2.6 gallons (9.8 liters)
• Coverage Area: Up to 600 square feet
• Output: Up to 2.3 gallons per day (under ideal conditions)
• Humidistat: Adjustable dial control
• Filter Type: Evaporative wicking filter (replaceable)
• Power: 120V AC, 60Hz
• Power Consumption: 40W (max)
• Unit Dimensions: 15.5" H x 12.5" W x 10.25" D
• Weight (empty): 7.5 lbs
• Noise Level: < 40 dB on low setting

Controls and Operation

Front Panel Controls: Power Switch, Humidistat Control Knob, Indicator Light.

Operation: Set humidistat to desired level (1-10 scale or %). Power ON starts fan. Unit runs until desired humidity is reached or tank is empty.

Adjustments: Turn knob clockwise to increase humidity output, counterclockwise to decrease. For continuous operation, set to maximum. For automatic operation, set to middle range (40-60%).

Indicator Lights: Power LED (green) indicates unit is on. Low water warning may flash when tank is nearly empty.

Maintenance & Cleaning

Regular cleaning prevents mineral buildup and ensures efficient operation.

1. Unplug unit and remove tank before cleaning.
2. Empty any remaining water from tank and base.
3. Clean tank with mild detergent and soft cloth. Rinse thoroughly.
4. Wipe base interior with damp cloth. Do not submerge base in water.
5. Clean exterior with dry or slightly damp cloth.
6. Allow all parts to air dry completely before reassembly.
7. Perform deep cleaning every 1-2 weeks during use.

Tip: Use white vinegar solution to remove mineral deposits (1 part vinegar to 3 parts water). Rinse thoroughly after.

Filter Replacement

The wicking filter should be replaced every 1-3 months depending on water hardness and usage.

1. Turn off and unplug humidifier.
2. Remove water tank from base.
3. Remove old filter from base slots.
4. Insert new filter, ensuring it sits properly in all slots.
5. Reinstall tank and plug in unit.
6. Run humidifier for 15 minutes to saturate new filter.

WARNING! Never operate without a filter. Using a worn filter reduces efficiency and may cause overheating.

Safety Features

Automatic Shut-Off: Turns off when tank is empty or improperly positioned. Tip-Over Protection: Unit shuts off if knocked over. Overheat Protection: Thermal fuse prevents overheating.

Care & Storage

When not in use for extended periods:

1. Unplug unit and empty all water.
2. Clean thoroughly as described in maintenance section.
3. Remove and discard old filter.
4. Allow all parts to dry completely.
5. Store in original box or cover in a cool, dry place.
6. Do not store with filter installed to prevent mold growth.

CAUTION! Never store with water in tank. Always clean before storage.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. UL Listed: Meets safety standards. Copyright © Honeywell International Inc. For support, visit www.honeywellhumidifiers.com or contact 1-800-332-1110.

Troubleshooting

Reset: Unplug for 5 minutes, then restart.

Service: 1-800-332-1110; www.honeywellhumidifiers.com