Honeywell Humidifier enviracaire Elite HE225B Manual

The Honeywell Humidifier enviracaire Elite HE225B is a high-performance evaporative humidifier designed to add moisture to dry indoor air, providing relief from dry air discomfort. It features a large-capacity water tank, adjustable humidity control, quiet operation, a wicking filter, an easy-to-clean design, and an automatic shut-off function. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Large water tank, Humidistat control, Wicking filter, Air outlet grille, Water tank handle, Power cord, Filter replacement indicator.

Installation

Unpack and inspect contents. Place on a flat, stable, and level surface.

1. Remove all packaging materials from the humidifier and tank.
2. Place the humidifier on a waterproof mat or towel in the desired location.
3. Ensure the unit is at least 6 inches away from walls and furniture for proper airflow.
4. Install the wicking filter: Remove from packaging, soak in water for 15-20 minutes, then insert into the base.
5. Fill the water tank with cool, clean tap water. Do not use hot water or additives.
6. Place the filled tank onto the base, ensuring it is seated properly.

WARNING! Do not place on carpets or uneven surfaces. Keep away from children and pets. Use only with 120V AC power.

First-Time Setup

After installation, prepare the humidifier for initial use.

1. Plug the power cord into a standard 120V AC electrical outlet.
2. Turn the humidistat control knob to the desired humidity setting (e.g., 40-50% for comfort).
3. Press the power button to turn on the unit. The power indicator light will illuminate.
4. Allow the unit to run for a few minutes to begin humidifying the air.
5. Adjust the humidistat as needed based on room conditions.

CAUTION! Always use two hands when carrying the filled water tank to prevent spills. Do not operate without the filter installed.

Specifications

• Model: HE225B enviracaire Elite.
• Type: Evaporative humidifier.
• Coverage Area: Up to 2300 square feet.
• Tank Capacity: 2.5 gallons.
• Output: Up to 2.5 gallons per day.
• Humidistat: Adjustable dial control.
• Filter Type: Wicking evaporative filter (replacement part #HEPA225).
• Power Source: 120V AC, 60Hz.
• Power Consumption: Low energy usage.
• Dimensions: Standard compact design.
• Weight (Empty): Lightweight for easy portability.

Controls and Settings

Front Panel: Power button, Humidistat control knob, Filter replacement indicator light.

Operation: Power button turns unit on/off. Humidistat knob adjusts desired humidity level (Low to High settings). Filter indicator light illuminates when it's time to replace the wicking filter.

Settings: Adjust humidistat based on room size and dryness. For larger rooms or drier air, set to a higher humidity level. For smaller spaces, use a lower setting to prevent over-humidification.

Connecting to Power

Use only a 120V AC outlet. Ensure the outlet is grounded and accessible.

1. Ensure the humidifier is off and the power cord is unplugged.
2. Plug the power cord directly into a wall outlet. Do not use an extension cord.
3. Turn on the humidifier using the power button.

Tip: Place the humidifier near the center of the room for even moisture distribution. Avoid placing near heat sources or in direct sunlight.

Operation

Designed for continuous operation to maintain comfortable humidity levels.

1. Fill the tank with clean, cool water daily or as needed.
2. Set the humidistat to your desired comfort level (typically 40-60% relative humidity).
3. The unit will run until the desired humidity is reached, then cycle on/off automatically.
4. When the tank is empty, the automatic shut-off will turn the unit off.
5. Refill the tank and the unit will resume operation once powered.
6. For optimal performance, keep doors and windows closed in the room being humidified.

WARNING! Never add essential oils, fragrances, or chemicals to the water tank, as this can damage the unit and void the warranty. Use only clean water.

Maintenance & Cleaning

Regular maintenance ensures efficient operation and prolongs unit life.

1. Daily: Refill water tank with clean water.
2. Weekly: Clean the water tank and base with a mild detergent and soft cloth. Rinse thoroughly.
3. Monthly: Deep clean the base and tank with a solution of white vinegar and water to remove mineral deposits.
4. Filter Replacement: Replace the wicking filter every 1-2 months during regular use, or when the filter indicator light turns on.
5. Always unplug the unit before cleaning.
6. Allow all parts to dry completely before reassembling and using.

CAUTION! Do not immerse the base unit in water. Do not use abrasive cleaners or brushes. Never operate without the filter installed.

Regulatory Information

FCC Compliance: This device complies with Part 15 of the FCC Rules. Copyright © Honeywell International Inc. Honeywell and enviracaire are trademarks of Honeywell International Inc. For support, visit www.honeywellpluggedin.com or contact Honeywell Customer Care at 1-800-332-1110.

Troubleshooting

Reset: Unplug unit for 10 seconds, then plug back in to reset electronic controls.

Service: 1-800-332-1110; www.honeywellpluggedin.com